2019 CVO Road Glide. Been wanting to do a stage 2 and was looking at the new CR-480 MT Monster Torque cam. Does anyone have experience with this cam?
I spoke to Fuel Moto about that cam yesterday. I noticed in their latest cam comparison they tested the old version (not the MT). I was curious how the MT performed compared to the old version. They told me they have not had a chance to test it yet.
Not much help, but sounds like it may be difficult to get info on it. Fuel Moto is usually one of the first to give results on new cams.
Zach
Check with Durwood, he tunes a lot of builds with CR cams.
just saw video by matt stephens from those dyno guys he has tuned several, starts earlier and goes longer good cam.
Quote from: tolobill on November 29, 2023, 06:41:22 AMjust saw video by matt stephens from those dyno guys he has tuned several, starts earlier and goes longer good cam.
I think we need to see many others use this cam professionally to see the broader outcomes.
Keen to hear what GMR thinks.
There always hype around these products.
I'm supposed to try one in a trike this week. Will post results in the dyno room.
Quote from: Sunny Jim on November 30, 2023, 06:23:33 AMQuote from: tolobill on November 29, 2023, 06:41:22 AMjust saw video by matt stephens from those dyno guys he has tuned several, starts earlier and goes longer good cam.
I think we need to see many others use this cam professionally to see the broader outcomes.
Keen to hear what GMR thinks.
There always hype around these products.
Agree. He tunes in-house at Cycle-Rama's facility. I'm sure it's a great cam but would like to see more of an unbiased result. I also wish they would show their dyno charts in SAE, the industry standard...
Wonderful folks over there at Cycle-Rama so no disrespect towards them at all.
Quote from: Mattls6 on November 30, 2023, 08:26:10 AMAgree. He tunes in-house at Cycle-Rama's facility. I'm sure it's a great cam but would like to see more of an unbiased result. I also wish they would show their dyno charts in SAE, the industry standard...
Wonderful folks over there at Cycle-Rama so no disrespect towards them at all.
I'm still trying to figure out how he tunes them in 1 1/2-2 hours. :idunno: His god like attitude also irritates me.
Quote from: lonewolf on November 30, 2023, 08:57:49 AMQuote from: Mattls6 on November 30, 2023, 08:26:10 AMAgree. He tunes in-house at Cycle-Rama's facility. I'm sure it's a great cam but would like to see more of an unbiased result. I also wish they would show their dyno charts in SAE, the industry standard...
Wonderful folks over there at Cycle-Rama so no disrespect towards them at all.
I'm still trying to figure out how he tunes them in 1 1/2-2 hours. :idunno: His god like attitude also irritates me.
He doesn't use TTS, so not as many tools available to him :teeth:
Quote from: Deye76 on November 29, 2023, 05:49:40 AMCheck with Durwood, he tunes a lot of builds with CR cams.
Yep, I would like to see his results with this cam.
Me too^^^^^^^^^^^^^^^
Quote from: nibroc on December 01, 2023, 03:35:58 PMMe too^^^^^^^^^^^^^^^
Don't be afraid, give him a call, he's straight up.
Quote from: biggzed on November 28, 2023, 05:58:41 PMI spoke to Fuel Moto about that cam yesterday. I noticed in their latest cam comparison they tested the old version (not the MT). I was curious how the MT performed compared to the old version. They told me they have not had a chance to test it yet.
Not much help, but sounds like it may be difficult to get info on it. Fuel Moto is usually one of the first to give results on new cams.
Zach
We have a good assortment of bolt in cams we're going fit into one of our test bikes this month, the CR-480MT and CR/APE-485 are among them as well as as the new Andrews 485 and 465B grinds. We're just finishing up testing about a dozen cams in the SE 135 crate motor and stock engine bolt in cam testing will commence next
Quote from: Jamie Long on December 01, 2023, 05:18:55 PMQuote from: biggzed on November 28, 2023, 05:58:41 PMI spoke to Fuel Moto about that cam yesterday. I noticed in their latest cam comparison they tested the old version (not the MT). I was curious how the MT performed compared to the old version. They told me they have not had a chance to test it yet.
Not much help, but sounds like it may be difficult to get info on it. Fuel Moto is usually one of the first to give results on new cams.
Zach
We have a good assortment of bolt in cams we're going fit into one of our test bikes this month, the CR-480MT and CR/APE-485 are among them as well as as the new Andrews 485 and 465B grinds. We're just finishing up testing about a dozen cams in the SE 135 crate motor and stock engine bolt in cam testing will commence next
Excellent. It's not lost on me (and I'm sure many on this forum) how much time, effort and cost goes in to doing these comparisons.
Zach
I tested that cam, and a couple others, in my tricycle. Link (https://harleytechtalk.com/htt/index.php?msg=1452075)
Quote from: : on December 09, 2023, 04:43:09 AMI tested that cam, and a couple others, in my tricycle. Link (https://harleytechtalk.com/htt/index.php?msg=1452075)
Excellent testing!