Anyone doing this? I am being cheap and trying to avoid buying the module to do carb bikes as I don't tune that many. But seem to have ended up with a half dozen or so lately. Anyone have a setup that works as good but cheaper?
I use a WEGO from DTT. It has dual sensors and a 5v output. I also have a WEGO III with live display and log installed on two of my bikes.
Quote from: turboprop on June 07, 2020, 11:15:41 AM
I use a WEGO from DTT. It has dual sensors and a 5v output. I also have a WEGO III with live display and log installed on two of my bikes.
Thanks!
Quote from: aharp on June 07, 2020, 10:04:13 AM
Anyone doing this? I am being cheap and trying to avoid buying the module to do carb bikes as I don't tune that many. But seem to have ended up with a half dozen or so lately. Anyone have a setup that works as good but cheaper?
What are you currently using for dyno hardware/software?
Quote from: Jamie Long on June 08, 2020, 02:37:17 PM
Quote from: aharp on June 07, 2020, 10:04:13 AM
Anyone doing this? I am being cheap and trying to avoid buying the module to do carb bikes as I don't tune that many. But seem to have ended up with a half dozen or so lately. Anyone have a setup that works as good but cheaper?
What are you currently using for dyno hardware/software?
Dynoware RT winpep 8
Quote from: aharp on June 08, 2020, 03:16:19 PM
Quote from: Jamie Long on June 08, 2020, 02:37:17 PM
Quote from: aharp on June 07, 2020, 10:04:13 AM
Anyone doing this? I am being cheap and trying to avoid buying the module to do carb bikes as I don't tune that many. But seem to have ended up with a half dozen or so lately. Anyone have a setup that works as good but cheaper?
What are you currently using for dyno hardware/software?
Dynoware RT winpep 8
What do you need to tune carbs that you don't already have?
Quote from: Jamie Long on June 08, 2020, 03:32:43 PM
What do you need to tune carbs that you don't already have?
I was under the impression that the AFR module from Dynojet was required in addition to the Dynoware RT module?
Quote from: aharp on June 08, 2020, 03:43:37 PM
Quote from: Jamie Long on June 08, 2020, 03:32:43 PM
What do you need to tune carbs that you don't already have?
I was under the impression that the AFR module from Dynojet was required in addition to the Dynoware RT module?
What do you use for AF data on your dyno?
Quote from: Jamie Long on June 08, 2020, 06:30:55 PM
What do you use for AF data on your dyno?
I usually have the Dynoware module plugged into the autotune module and i get the live AF data on the screen so i can keep track of where it's at when collecting data in autotune
Quote from: aharp on June 08, 2020, 07:13:50 PM
Quote from: Jamie Long on June 08, 2020, 06:30:55 PM
What do you use for AF data on your dyno?
I usually have the Dynoware module plugged into the autotune module and i get the live AF data on the screen so i can keep track of where it's at when collecting data in autotune
You can plug any Dynojet single or dual channel wideband Auto Tune device straight into the Dynoware RT stack via CAN, you will mount the O2 sensors in the pipes or use O2 blocks same as you would for an EFI bike
Quote from: Jamie Long on June 08, 2020, 07:33:49 PM
You can plug any Dynojet single or dual channel wideband Auto Tune device straight into the Dynoware RT stack via CAN, you will mount the O2 sensors in the pipes or use O2 blocks same as you would for an EFI bike
I didn't consider trying that, thanks Jamie. I guess I thought the autotune module would only be cable of, well, autotuning :sheep: :doh:
I prefer WB o2 Sensors 1/4"x#20 Adapter in an installed brass thread and closing it with a 1/4"x#20x1/2" Screw and a Copper Crush Washer. The 02 will provide data viewing in real-time for your adjustments in Graph or Cell. Most softwares will record for play back on a time use basis.
Way more inexpensive that most setups and only calibration about every 50 uses.