Putting the cam chest back together on my 80 FXS engine and notice that the feed hole in the rear lifter block gasket does not line up well with the feed hole in the engine case. The front one lines up very well. Should I find a new rear gasket or not sweat it?
IMG_0213.jpg
I have an 80' FXWG. It's been a while, but the last time I replaced Lifter Block Gaskets they lined up correctly. James Gasket Kit...I believe.
I'm a bit picky about that kind of stuff.
I think I would try other Gaskets instead of leaving it and finding out the hard way.
Good Luck!
You could carefully trim that side of the oil hole in the gasket.
But does the rest of the gasket line up where it's supposed to?
(https://imgsh.net/i/rBvj88e.png)
Upon closer inspection, no, it doesn't line up well. If I line the large hole up well the feed hole is even more covered. These are from Reliant. I've had good luck with them in the past but I don't feel good using this one. They were supposed to arrive last Monday but they didn't arrived until yesterday. I think it took them four days to get out of Texas. Seriously. I'll let you now what they say but I'm tempted to just try another brand from somebody a little closer to the northeast. Thanks for the replies.
IMG_0214.jpg
It's been a lot of years since I held those gaskets in my hands. Could they have given you two front gaskets?
Quote from: Ohio HD on February 11, 2023, 03:05:42 PMIt's been a lot of years since I held those gaskets in my hands. Could they have given you two front gaskets?
Looks like I have one of each.
IMG_0217.jpg
I would bet that your HD dealer probably has them. They fit from 1948 to 1999.
18633-48D rear tappet guide gasket
18634-48C front tappet guide gasket
Just a guess can you flip them over and use in other base or no ? Again just an idea
Line it up and trim the hole or use a gasket punch,there is lots of gasket surface to work with.This has been common practice from 1955 on.
Brian, Thanks for the p/n's. I'm not sure that the nearest dealer would have them, they run pretty lean in that area. I'll have to wait until Tuesday to check before I drive down. I sent Reliant an email and a couple of photos so maybe I'll hear from them tomorrow.
72fl, Those gaskets only work one way, one side and one side up only. Thanks for the suggestion though.
RTMike, I gave that some thought but those are foamet with the metal core and I really don't have a good way to enlarge that feed hole w/o buggering it up.
If I had a choice I'm not sure that I'd use it as is either, perhaps in a pinch, however...
If you did use it, it would work fine. Once the the tappet is pressurized there is very little oil flow. Even restricted, more than enough oil is going to get to that tappet. It appears to be more of an aesthetic dillemma than a functional one.
-JW
If I had to use it I would work on it with a very sharp X-Axto knife and cut it back.
I'd swap the front and rear around just to check...then if I decided to open the hole up I'd use a leather punch on a wood block
Quote from: Hossamania on February 12, 2023, 10:12:42 AMIf I had to use it I would work on it with a very sharp X-Axto knife and cut it back.
Somewhere around here in Nancy's plethora of craft supplies is an X-Acto knife kit with a fairly large selection of blades. Now where did I see that last? :idea: Thanks, Hoss
Quote from: thumpr54 on February 12, 2023, 11:32:18 AMI'd swap the front and rear around just to check...then if I decided to open the hole up I'd use a leather punch on a wood block
Each is dedicated, they're not interchangeable. Will probably try some surgery if I can find that little knife kit.
I don't know JW. When I enlarge the pic it looks like it's heavy paper without any metal centre wafer. He may get lucky with the razor knife.
Quote from: kd on February 12, 2023, 05:52:13 PMI don't know JW. When I enlarge the pic it looks like it's heavy paper without any metal centre wafer. He may get lucky with the razor knife.
I found the X-Acto knife kit. The gasket looks/feels like it's has a metal core (enlarge pic, gasket is on its side). Got to get some breakfast in me then I'll see about enlarging that hole.
If it has a metal wafer you may find yourself reverting to a small dremel tool bit as JW suggested.
I tried a Dremel and ended up fubar-ing the gasket. I have a pair of new ones on the way from an on line source in case the local dealer doesn't have any in stock. Was reminded that my 1/4" drive 1/4 in. 12-pint socket went awol a while ago and I need to replace it. Four auto jobbers and two big box stores in this town yet nobody had one so on line we go again. It's close by so should beat the new gaskets here. The lifters/blocks are the older VelvaTouch for Shovelhead cams. I've had them for at least twenty years. Just want to be sure that they get all the oil that they need. They still look great. Have yet to hear back from Reliant.
I still think you can cut thru it with a good X-Acto knife. Give it a try on the one you modified with the Dremel. Might need to do it with the next set too, it would be nice to know it can be done.
Quote from: billbuilds on February 13, 2023, 01:43:29 PMI tried a Dremel and ended up fubar-ing the gasket. I have a pair of new ones on the way from an on line source in case the local dealer doesn't have any in stock. Was reminded that my 1/4" drive 1/4 in. 12-pint socket went awol a while ago and I need to replace it. Four auto jobbers and two big box stores in this town yet nobody had one so on line we go again. It's close by so should beat the new gaskets here. The lifters/blocks are the older VelvaTouch for Shovelhead cams. I've had them for at least twenty years. Just want to be sure that they get all the oil that they need. They still look great. Have yet to hear back from Reliant.
As JW had said once under pressure it should be fine. But I'm like you, I want the entire oil passage opened. Velva Touch lifters were the answer for Shovel motors.
Quote from: Hossamania on February 13, 2023, 02:01:28 PMI still think you can cut thru it with a good X-Acto knife. Give it a try on the one you modified with the Dremel. Might need to do it with the next set too, it would be nice to know it can be done.
Sorry, I kind of skipped over that part. I attempted to cut thru the metal core with the X-Acto but it wasn't going to happen. Got a few small flecks by making 1/4 turn passes with a very small blade. Came to the realization that it would take forever that way and turned to the Dremel. I'm not going to admit once again how that went. :embarrassed:
I imagine as soon as the blade hit you said a curse word or two as the shreds went flying...
If you ever have to enlarge or alter a hole in a gasket like that again, here's the trick:
Get two strips of anything that is hard and flat, wood or metal, and two nuts & bolts. Clamp the strips together and drill two holes that are a snug fit for your two nuts & bolts. Then drill another hole between the bolts that is the size you want for the gasket hole. Mark the gasket where it needs to be trimmed, line it up between the strips, tighten the bolts, and go to work. It helps to put the assembly in a vise, or clamp it to a bench so you are not trying to hold everything in your hands. Safety.
Brilliant!
for me id get the right gaskets
By the right gaskets do you mean paper ones David Lee? Because the dealership had the paper style gaskets in stock though the rear feed hole still did not line up well so I enlarged it with the X-Acto knife. Maybe way anal but I feel better putting it together after having opened it up and then applying a light coat of spray copper.
SP33DY, That's a greet idea. The other set of gaskets that I have coming in the mail are metal core. Will keep your trick in mind for down the road. Thanks
I have used one of these before with great success
https://www.thesupplyguy.us/product-p/SG-DISC.htm?gclid=Cj0KCQiAorKfBhC0ARIsAHDzsls4CpMxStTvKycFUcua5zCe-XtzMTVYdIUmLSwRtNnIsDGg_2sE0GIaAhFmEALw_wcB
Interesting. Use in a shop press? Country of origin?
-JW
James gaskets never an issue. Mi 2 bits
Quote from: JW113 on February 15, 2023, 02:23:32 PMInteresting. Use in a shop press? Country of origin?
-JW
Looks just like the used kit on eBay - made in China.
Quote from: JSD on February 15, 2023, 06:35:42 PMJames gaskets never an issue. Mi 2 bits
Which ones? They're available in .020 paper, .031 paper and foamet (metal core).
Quote from: billbuilds on February 16, 2023, 03:38:25 AMQuote from: JW113 on February 15, 2023, 02:23:32 PMInteresting. Use in a shop press? Country of origin?
-JW
Looks just like the used kit on eBay - made in China.
The one I use is made by Precision and made for cutting shim stock. Just line up where you want the hole and smack it with a hammer
Quote from: billbuilds on February 16, 2023, 03:53:48 AMQuote from: JSD on February 15, 2023, 06:35:42 PMJames gaskets never an issue. Mi 2 bits
Which ones? They're available in .020 paper, .031 paper and foamet (metal core).
I have only used paper cant comment on new type
I use the gaskets from S&S.
Quote from: wfolarry on February 17, 2023, 06:25:03 AMI use the gaskets from S&S.
S&S p/n 33-5302 for the pair. Looks like they may well have been private labeled with the S&S logo by the gasket manufacturer. The ones I got from the dealer are made by Lydall/Interface Materials (formerly Armstrong). Apparently they are now a division of AFG - Accurate Felt & Gasket.