I have a Fireball Hi-4tc installed but have no real experience with them so I am looking for PDF's or any information (as well as the optional software) .... any opinions would be welcomed...
here's the limited instructions that come with the ignition:
(http://i381.photobucket.com/albums/oo256/wannabmayor/HTT%20hosted%20pictures/Craneignition_1.jpg)
(http://i381.photobucket.com/albums/oo256/wannabmayor/HTT%20hosted%20pictures/Craneignition_2.jpg)
(http://i381.photobucket.com/albums/oo256/wannabmayor/HTT%20hosted%20pictures/Craneignition_3.jpg)
(http://i381.photobucket.com/albums/oo256/wannabmayor/HTT%20hosted%20pictures/Craneignition_4.jpg)
thanks to another member, I was able to get a copy of the ignition maps that's on the module:
(http://i381.photobucket.com/albums/oo256/wannabmayor/HTT%20hosted%20pictures/curve0.jpg)
(http://i381.photobucket.com/albums/oo256/wannabmayor/HTT%20hosted%20pictures/curve1.jpg)
(http://i381.photobucket.com/albums/oo256/wannabmayor/HTT%20hosted%20pictures/curve2.jpg)
(http://i381.photobucket.com/albums/oo256/wannabmayor/HTT%20hosted%20pictures/curve3.jpg)
(http://i381.photobucket.com/albums/oo256/wannabmayor/HTT%20hosted%20pictures/curve4.jpg)
(http://i381.photobucket.com/albums/oo256/wannabmayor/HTT%20hosted%20pictures/curve5.jpg)
(http://i381.photobucket.com/albums/oo256/wannabmayor/HTT%20hosted%20pictures/curve6.jpg)
(http://i381.photobucket.com/albums/oo256/wannabmayor/HTT%20hosted%20pictures/curve7.jpg)
(http://i381.photobucket.com/albums/oo256/wannabmayor/HTT%20hosted%20pictures/curve8.jpg)
(http://i381.photobucket.com/albums/oo256/wannabmayor/HTT%20hosted%20pictures/curve9.jpg)
the above maps are what you get based on the perspective curve settings with the initial timing set to 5. You can then retard the whole curve by 5 degrees or advance it 4 degrees by adjusting the initial timing.
HTH,
mayor
WOW thanks Mayor. I have been searching for that today! :up:
What is the exact model, quite a few are available, 2 connector, 1 connector, etc. The number will be in the lower right hand corner, similar to 8-3180 ?
You could need Install_hi4tc_Rev_9000-3150 , or Install_hi4tc_Rev_9000-3170 , or Install_hi4tc_Rev_9000-3180
The model I have is B 3170
Install_HI4TC_Rev_9000-3170 PDF (http://www.box.net/shared/qdl379xtaz)
PC Link HI-4TC Software & Cable 8-3180 PDF (http://www.box.net/shared/97d6m8oq8g)
PowerLink_Software_&_Cable_8-3251B PDF (http://www.box.net/shared/lcf61q4lsh)
Remind me again what TC you have. :teeth:
no problem Jim. :up: I was searching for that for 2 years. :teeth:
I got one here on the dyno,well it was until the starter clutch went south. :down:
so I didnt have 2 years LOL
Thanks again that was very timely :up:
wish it was EFI . GETTING TIRED OFF SMELLING LIKE GAS!
Quote from: strokerjlk on November 07, 2010, 05:10:17 AM
wish it was EFI . GETTING TIRED OFF SMELLING LIKE GAS!
all that fancy efi stuff just makes you lazy. :teeth: I can relate completely. :embarrassed:
Nice job Mayor, this kind of help is what makes this site so great... :up:
thanks, but the thanks should really go to hrdtail...he's the one that provided me the info. :teeth:
thanks again from China Twin 88 :bike:
Sorry hardtail, I just scanned the thread and did not read it all, Nice Job :up:
Been reading the info from the PDFs and thanks greatly for the instruction sheet...looks like I did it right...parts are "strange" when your a "stranger" in China....When I got this bike it had a lot of evo parts on it as well as a box of new fangled gadgets ..... seems to be running fine though .. now if I can resist the urge to try and tweak it to the Dark Side....
a big shout out for Mike Covello, Customer Sales and Technical Support, Crane Cams who answered my questions right away and offer additional help. Thanks to all HTT members for their potential and present offers of assistance. Great being part of this online community.